Ateis IDA8C Instrukcja Użytkownika

© 2012 ATEÏSIDA8 & Ateis StudioUser ManualVersion 1.0.1

Ateis Studio10© 2012 ATEÏS1 Introduction1.1 WelcomeThank you for choosing ATEÏS. We here at ATEÏS hope you will enjoy our technology as much as weenj

Ateis Studio100© 2012 ATEÏS4.1.6.5 Normal Amplifier MonitoringSettingsFirst, in Ateis Studio, right click on IDA8C/S block in [Devices] window:Window

Product Features 101© 2012 ATEÏSTo determine the boundary of fault detection for selected zone. There is a fault recognized if oneof follow conditions

Ateis Studio102© 2012 ATEÏSFaultsAmplifier Gain Too HighIf Measure > (Unloaded Reference x (100% + Tolerance%)), an Amplifier Gain Too High fault i

Product Features 103© 2012 ATEÏSWindows [Monitor(Matrix Mode) - IDA8C/S X] opened, select page [Backup Amplifier Settings]:AmplifierIndicate which bac

Ateis Studio104© 2012 ATEÏSGet ReferenceGet the reference values of selected zone for further fault detection. Be aware, hardwareconfigur

Product Features 105© 2012 ATEÏSo Make sure there is good connection between speaker and IDA8C/S.o Ensure the speaker is a good one.o Check gain of am

Ateis Studio106© 2012 ATEÏS4.1.6.7 Global SettingsThere are global settings listed below:Enable MonitorA check box to determine enable or disable moni

Product Features 107© 2012 ATEÏS4.1.6.8 Tone SettingsIn the lower part of window [Monitoring(Matrix Mode)-IDA8C/S X ], There is a page [Tone Settin

Ateis Studio108© 2012 ATEÏSEnable 1K tone for monitoring. If this option is on, during Start Time and End Time, a 1K tonesignal send to amplifier for

Product Features 109© 2012 ATEÏS4.1.8 Contact I/O4.1.8.1 Evacuation InputIDA8 Devices have evacuation inputs that allow the monitoring of external con

Introduction 11© 2012 ATEÏSHotelsRestaurantsShopping mallsTheme parksPlaces of worshipStadiaMuseumsIndustrialUniversity and campus applications

Ateis Studio110© 2012 ATEÏSUse Evacuation Input componentBy use Evacuation Input component, you can control the other logic components. Logic signal i

Product Features 111© 2012 ATEÏSUse Logic Out componentBy using Logic Out component, you can output signal coming from any logic component. ple

Ateis Studio112© 2012 ATEÏSThere are three types of redundancy unit:RU-MAIN.: Switch digital audio and processing matrix like IDA8C, paging consoles a

Product Features 113© 2012 ATEÏS2. Search primary and secondary IDA8C using Ateis Studio, and connect to them.3. Select the IDA8C to be primary, Clic

Ateis Studio114© 2012 ATEÏS6. Press button [Configure], A window shows message "Redundancy Configuration Success" if theprocedure

Product Features 115© 2012 ATEÏS7. After this setting was finished, you can see the information on devices window show the two IDA8Care redundancy for

Ateis Studio116© 2012 ATEÏS4.2.1.3 RU-Main4.2.1.3.1 Overview

Product Features 117© 2012 ATEÏSRU-MAIN is a device for audio processor redundancy, the peripherals are connected with RU-MAIN notdirectly to audio pr

Ateis Studio118© 2012 ATEÏS1. PDC Audio Output for RecordThe audio output of peripheral plugged on PDC connector.2. PDC ConnectorsThere are 2 sets of

Product Features 119© 2012 ATEÏSmonitor S_WD to determine which one can be active.8. P_ACT(Primary Active Output)Output a logic signal to indicate pri

Ateis Studio12© 2012 ATEÏS1.3 EC Declaration of Conformity

Ateis Studio120© 2012 ATEÏS15.Backup Amplifier OutputThere are two backup amplifier outputs on RU-MAIN, each output consist of three connectors:P_AMPO

Product Features 121© 2012 ATEÏSactive one of them. If primary audio processor is active, all signal of peripherals are redirect to primaryaudio pro

Ateis Studio122© 2012 ATEÏSPDC NConnect to peripheral which communicates to audio processor using PDC interface, for examplePSS AS, PPM AS.S_PDC NConn

Product Features 123© 2012 ATEÏS"(S_WD)Secondary Watching Dog".12.Master/Slave SwitchA dip switch to set RU-PDC be master or slave. The di

Ateis Studio124© 2012 ATEÏSRU-CTL is a device for audio processor redundancy, the peripherals are connected with RU-CTL notdirectly to audio

Product Features 125© 2012 ATEÏS2. Expansion Power SupplyOutput 24V DC power to next RU-MAIN/PDC/CTL devices.There are two connectors of this output:P

Ateis Studio126© 2012 ATEÏS"(S_WD)Secondary Watching Dog".11.Master/Slave SwitchA dip switch to set RU-PDC be master or slave. The differe

Product Features 127© 2012 ATEÏS2. One zone connects many loudspeakers, and installed the loudspeakers by circularity and thedistance is no

Ateis Studio128© 2012 ATEÏS4. In a large area, the broadcast source is same in the area, and the distance of each loudspeakeris far, maybe the ambien

Product Features 129© 2012 ATEÏSNote: The sound of loudspeakers from another zone can't effect each other, otherwise, the DNM willconsider the so

Safety Declartion 13© 2012 ATEÏS2 Safety DeclartionDo not expose the device to extreme temperatures, direct sunlight, humidity, or dust, wh

Ateis Studio130© 2012 ATEÏS3. Connect to the IDA8C/S4. Click the button [Remote Plug-In]5. A window [Remote Plug-In] pop up. Select RS485 port number

Product Features 131© 2012 ATEÏS6. In device editing window, create a DNM and wires it to IDA8C/S's RS485 port:7. Double click the IDA8C/S to

Ateis Studio132© 2012 ATEÏS8. Go back to device editing window, click on the block of DNM device. A [DNM Preset] window popsup. There is a combo bo

Product Features 133© 2012 ATEÏS10.Store the configuration, and then online.11.Click "DNM" component to open it's element window

Ateis Studio134© 2012 ATEÏS12.After the calibration is successful, the green LED will light up, and the DNM will start to work.13.If the White Noise L

Product Features 135© 2012 ATEÏS14.If the White Noise Level goes down to -40dB and the over LED is lighted up, this means thecalibra

Ateis Studio136© 2012 ATEÏS4.2.2.5 Operation NoticeOnce the calibration is successful, don't adjust the level in the rear of DNM component (ex: M

Product Features 137© 2012 ATEÏS2. After connecting two DNM one by one, then connect the DNM to a series. Click the “Refresh” buttonto read back the

Ateis Studio138© 2012 ATEÏS4. To assign the DNM component to device.

Product Features 139© 2012 ATEÏS5. Draw DSP DNM component, and connect the input and output.6. To modify the DSP component name. You can simply use pr

Ateis Studio14© 2012 ATEÏSTo prevent the unit from falling down and causing personal injury and/or property damage, avoidinstalling or mounting the un

Ateis Studio140© 2012 ATEÏS7. Go to device editing window. Double click the device DNM component to open a window, and Linkdevice DNM component

Product Features 141© 2012 ATEÏS4.2.3 PPM AS4.2.3.1 OverviewUnidirectional Condenser Addressable Microphone, compatible with all system units, PPM AS

Ateis Studio142© 2012 ATEÏS4.2.3.2 Control Panel1. MicrophoneThe sleek condenser gooseneck microphone. This unidirectional condenser microphone warran

Product Features 143© 2012 ATEÏS Plug-in" make audio processor to recognize the peripheral devices. 5. Power LEDThis LED light up when the PPM AS

Ateis Studio144© 2012 ATEÏSDC Input18V~26V, Typical 24V120mAMicrophone OutputMaximum level = 6dBu.Output Impedance = 100Ohm.THD @ 1kHz < 1%.Bandwid

Product Features 145© 2012 ATEÏSDSP component configurationIt need to route audio from PPM AS to paging component for paging processing. See the follo

Ateis Studio146© 2012 ATEÏSPPM AS ManagerPPM AS Manager is an unit of the software to manage settings about PPM AS that connect toaudio proce

Product Features 147© 2012 ATEÏSKey-Priority(todo: rider)The priority of key.Key-CountTo specify how many keys on PPM AS.Pre-Announcement-EnabledEnabl

Ateis Studio148© 2012 ATEÏSPathSpecify the directory to list all files with supported formats.File ListDisplay files in the directory Path.DisplaySpec

Product Features 149© 2012 ATEÏSClear the list.o CloseClose the window.PPM AS SettingsDouble click the PPM AS object open the window of PPM AS Setting

Quick Start 15© 2012 ATEÏSConnect ethernet wire for device and PC.IDA8C.2. Power up devicePower up device and make sure power LED is on.3. Set IP, Sub

Ateis Studio150© 2012 ATEÏSmore details.Remote Plug-inIt need to do a "Remote Plug-in" to make audio processor recognize this remote devices

Product Features 151© 2012 ATEÏSThe PSS AS touch paging microphone console is a man-machine interface which allows paging call,messages broadcas

Ateis Studio152© 2012 ATEÏSA back-lit touch screen with 5" diagonal and 800 x 480 resolution contains 14 pages, 12 keys foreach pages can free

Product Features 153© 2012 ATEÏSFront Panel SpeakerImpedance = 4Ohm.Maximum Power @ 1kHz = 1W.THD @ 1kHz < 1%.Bandwidth @ -3dB = 200Hz ~ 12kHz.Maxi

Ateis Studio154© 2012 ATEÏSexample:Pin A~D of RS485 Input component is corresponds to PPM AS 1~4 audio plugged in PDC1~4respectively. Netw

Product Features 155© 2012 ATEÏSKeyRefer to the key on the page of PPM AS.Comment 1/2/3The text displayed on the key, there are three rows on it Comme

Ateis Studio156© 2012 ATEÏSValueTo specify which code on integration paging event is bound with the key. AllSelect all zone for the key.Zone Selection

Product Features 157© 2012 ATEÏSEventSelect the event linked to.the key.Control ModeSpecify the control mode is Trigger or Control, see more details o

Ateis Studio158© 2012 ATEÏSThis section is talking about to setup the message list for play on runtime in PSS AS. Beforeselection, you n

Product Features 159© 2012 ATEÏSThis section is settings about chimes.Chime ListOpen a settings window to build up list of message for selection.Pre-a

Ateis Studio16© 2012 ATEÏSClick [LOGIN] in [SYSTEM SET MENU-1] page:Click [USER NAME] in [LOGIN] page:Input ID "ADMIN" which is the default

Ateis Studio160© 2012 ATEÏSAssign to Design ObjectsThe device object in design window needs map to physical device, then the configuration

Product Features 161© 2012 ATEÏS4.2.5.2 Control Panel1. OLED Display2. Exit ButtonBack to the main menu.3. KnobTurn: Select items or change volume.Pre

Ateis Studio162© 2012 ATEÏSMaximum Cable Length1200m on Category 5 cable4.2.5.4 ConfigurationTo make URC AS work it need to edit configuration using

Product Features 163© 2012 ATEÏSSerial NumberSerial number of the URC AS.NameName of the URC AS.MemoryIndicate memory usage of the URC AS for current

Ateis Studio164© 2012 ATEÏSTextThe text in About text list.AddTo add a text in About text list.DeleteTo remove selected text from About text list.URC

Product Features 165© 2012 ATEÏSo Check boxes for selection of master/sub presets to be linked to the item.o Check All button to select all master/sub

Ateis Studio166© 2012 ATEÏSItemIndex of the item.LabelThe display text of the item.Control TypeThe type of item. refer to prior section "Function

Product Features 167© 2012 ATEÏStopic Remote Plug-in for more details.Assign to Design ObjectsThe device object in design window needs map to ph

Ateis Studio168© 2012 ATEÏSMonitoring resistor = 4.7k Ohm.Evacuation Inputs(Voltage Mode)On Voltage:ItemMinimumMaximumUnitVoltage1872VDC4.2.6.3 Config

Product Features 169© 2012 ATEÏS4.2.7 CD-Touch4.2.7.1 OverviewCD-Touch Wall mounted cabinet remote paging console for Ateis audio processor.Wall-mount

Quick Start 17© 2012 ATEÏSA page showing the message to prompt login is success:Go back to [SYSTEM SET MENU-2] page, click [ETHERNET]There are three f

Ateis Studio170© 2012 ATEÏS4.2.7.2 Control Panel1. Fireman Microphone HookAn U-shape hook to place fireman microphone.2. MicrophoneNot used.3. Power I

Product Features 171© 2012 ATEÏSNo function for the moment.9. Middle ButtonNo function for the moment.10.Right ButtonNo function for the moment.11.Tou

Ateis Studio172© 2012 ATEÏSBandwidth @ -3dB = 50Hz ~ 20kHz.Maximum Cable Length100m on Category 5 cable4.2.8 CD84.2.8.1 OverviewCD8 Wall mounted cabin

Product Features 173© 2012 ATEÏSyet makes outlets easy to connect via a standard RJ45 connector.4.2.8.2 Control Panel1. Fireman Microphone HookAn U-sh

Ateis Studio174© 2012 ATEÏS6. Monitoring SpeakerThis embedded speaker to play chime when paging or monitor signal from audio processor, it needsto wor

Product Features 175© 2012 ATEÏSBandwidth @ -3dB = 200Hz ~ 20kHz.Front Panel SpeakerImpedance = 8Ohm.Maximum Power @ 1kHz = 1W.THD @ 1kHz < 1%.Band

Ateis Studio176© 2012 ATEÏSand DATA.The unit comprises of 16 zones / 16 buttons with fist firemen’s microphone in a metal surface mountwall-box

Product Features 177© 2012 ATEÏSColorStatusFrequencyActivityRedPermanentPriority of the zone is lower than other sources.GreenBlinking ° ° Priority

Ateis Studio178© 2012 ATEÏSPlease refer to Hold Indicator(1~8).14.Event Select Key(9~16)Please refer to Event Select Key(1~8).15.Power IndicatorThis L

Product Features 179© 2012 ATEÏS4.2.10 Fireman Microphone4.2.10.1 OverviewThe Fireman Microphone SHM 1 is a small compact microphone dedicated to

Ateis Studio18© 2012 ATEÏS You need to reboot device take effect.4. Install Ateis Studio5. Run Ateis Studio6. Network settings of Ateis StudioIf there

Ateis Studio180© 2012 ATEÏSSee more details in topic Fireman component.

Product Features 181© 2012 ATEÏS4.2.11 CDPA4.2.11.1 OverviewCDPA Wall mounted cabinet remote paging console for Ateis audio processor. Wall-mount heav

Ateis Studio182© 2012 ATEÏSAdditional RCA connectors with selection buttons support local audio injection for commercial usage.The RS485 communication

Product Features 183© 2012 ATEÏSStatusFrequencyActivityPermanentThere are faults in audio processor.Blinking ° ° Lost communication with audio proce

Ateis Studio184© 2012 ATEÏSThese LEDs Indicate which keys are selected.16.Event Select Key(1~8)These buttons are used to select keys, each key ma

Product Features 185© 2012 ATEÏS4.2.12 PCP4.2.12.1 OverviewWall-mount heavy duty remote paging console with Access level 2 protection to comply with t

Ateis Studio186© 2012 ATEÏS4.2.12.2 Control Panel1. A telephone styled microphone for paging.2. Busy Indicator(1~8)Show the status of zone:ColorStatus

Product Features 187© 2012 ATEÏSStatusFrequencyActivityPermanentThere are faults in audio processor.Blinking ° ° Lost communication with audio proce

Ateis Studio188© 2012 ATEÏS4.2.12.3 CharacteristicsCaseDimension = 346 mm (W) x 220 mm (H) x 128 mm (D).Weight = 3 Kg.Color = RAL7035.PowerItemVoltage

Product Features 189© 2012 ATEÏS4.2.13 PSC4.2.13.1 OverviewUnidirectional Condenser Addressable Microphone, compatible with all system units,

Quick Start 19© 2012 ATEÏSThere are three pages on the right side of window, select [Network] page. Choose the right networkinterface card on NIC fiel

Ateis Studio190© 2012 ATEÏS4.2.13.2 CharacteristicsCaseDimension = 220mm (W) x 483mm (L) x 115.7mm (H).Weight = 0.37 Kg.Color = RAL7035.PowerItemVolt

Product Features 191© 2012 ATEÏS4.2.14 URC200 TPC4.2.14.1 OverviewThe URC200 is an programmable remote controller (TCP/IP) for the IDA8 system,

Ateis Studio192© 2012 ATEÏS4.2.14.2 Control Panel1. TFT PanelA color 2" TFT panel presents the menu system of URC 200 TPC.2. IR ReceiverIt receiv

Product Features 193© 2012 ATEÏSItemVoltageCurrent ConsumptionCommentDC Input18V~26V, Typical 24V50mAMaximum Cable Length100m on Category 5 cable4.2.1

Ateis Studio194© 2012 ATEÏS3. Press button [Reset] to make the reset root menu to default.4. Click the button on field [Link] for the desired menu ite

Product Features 195© 2012 ATEÏS5. The default name is "Group 1", you can change it to the other string.6. Click buttons on the field [Link]

Ateis Studio196© 2012 ATEÏS7. For example, I create two items: "increase" and "decrease" for controlling the audio level.8. Clink

Product Features 197© 2012 ATEÏSThe fields in the grid are described below:TypeTo indicate the communication protocol used, this field is read only.IP

Ateis Studio198© 2012 ATEÏS4.2.14.4.2 Import/Export ConfigurationYou can export the URC200 TPC configuration to a file or import the file to restore

Product Features 199© 2012 ATEÏSAfter power up, you'll the a message on the top of LCD screen: "No Preset". It means the URC200 TPCnow

2012/07/11Revision History1.0.0 Time Version The First Version.2012/07/23 1.0.1 Modified DNM chapter in the Product Featu

Ateis Studio20© 2012 ATEÏSAfter few seconds, devices are listed by tree structure on [Devices] field, IP address of the device wewant to config is 192

Ateis Studio200© 2012 ATEÏS2. Click page [Remote Device]. This page lists all devices in the network. Press the button [Search] todiscovery URC200 TPC

Product Features 201© 2012 ATEÏS4. There is a box [Function List] at the right side of the window. By select the entry of the grid, the itemsinside th

Ateis Studio202© 2012 ATEÏS4.2.14.5.2 Protected ModeThere are some internal settings of URC200 TPC. Those settings are in the protected mode menu. T

Product Features 203© 2012 ATEÏSVersionThis page displays the firmware version of URC200 TPC.S. B.This page is comprised of two settings:Saver Time:Th

Ateis Studio204© 2012 ATEÏS4.2.15 PPM-IT54.2.15.1 OverviewThe PPMIT5 IP paging console is a man-machine interface which allows call-paging,

Product Features 205© 2012 ATEÏSAll the settings are done through web pages with your favorite web browser. Thanks to powerful echocancellation

Ateis Studio206© 2012 ATEÏSSPA 2060SPA 2120SPA 2240The SPA amplifiers were specifically developed to meet the requirements of EN 60849 fo

Product Features 207© 2012 ATEÏSA surveillance circuit continuously monitors the temperature and the presence of AC and DC powersupplies fo

Ateis Studio208© 2012 ATEÏSchecking the level of the input signal. Temp.If the device internal temperature exceeds 95 degrees C, the TEMP LED will lig

Product Features 209© 2012 ATEÏSmains power lead fitted with an IEC connector.For 115 V, fuse rating: SPA 2060: 2.5ASPA 2120: 5ASPA 2240: 8AFor 230 V,

Quick Start 21© 2012 ATEÏS9. Check compatibility between device and Ateis Studio. Click [Read Version] of menu.A window [Version] opened, press button

Ateis Studio210© 2012 ATEÏSPowerItemVoltageCurrent ConsumptionCommentAC Input230V +/- 10%1.2AFrequency:47Hz~63HzDC Output21~28V, Typical: 24V1AAudio F

System Functionality 211© 2012 ATEÏS5 System Functionality5.1 Ateis Studio5.1.1 Overiew of Ateis StudioAteis Studio allows complete audio systems

Ateis Studio212© 2012 ATEÏSIn addition you will find a comprehensive selection of tools for system design and programming using ourAteis Studio integr

System Functionality 213© 2012 ATEÏS5.1.3 Install Ateis StudioPlease follow the steps below to install Ateis Studio:1. Before installing the Ateïs Stu

Ateis Studio214© 2012 ATEÏSClick [Next]5. Type in user name and your organization name if you want and click [Next]

System Functionality 215© 2012 ATEÏS6. By default the program the software is installed under the path "C:\Program Files\ATEIS\ATEIS Studiovx.x.x

Ateis Studio216© 2012 ATEÏS8. Wait until the end of installation.9. After all installation tasks have been finished successfully click [Finish] to exi

System Functionality 217© 2012 ATEÏS10.The installation program creates a shortcut to the "ATEIS Studio v.1.x.x .exe" named "ATEIS Stud

Ateis Studio218© 2012 ATEÏS5.1.4 Windows LayoutThe basic windows layout should like the figure showed above, but the layout can be changed if you drag

System Functionality 219© 2012 ATEÏS7. Status BarDisplay the status of software, including the modification indication of editing file, mouse

Ateis Studio22© 2012 ATEÏSA window [Device Select] opened allow the target IDA8 be selected, click button [OK]:A file manager opened. Goes into direct

Ateis Studio220© 2012 ATEÏS5.1.6 EditSelect All o Select all the components and wires.SelectSelect All DSP Components o Select all DSP components in t

System Functionality 221© 2012 ATEÏS5.1.7 ViewEach item in the [View] menu can open a specific window to do settings modification or management ofdevi

Ateis Studio222© 2012 ATEÏSProperties Open the window of Properties which allow you to inspect various parameters of an object in graphiceditor.PPM AS

System Functionality 223© 2012 ATEÏSZoom in the graphic editor.Zoom Out Zoom out the graphic editor.Zoom Original Zoom to original size of graphic edi

Ateis Studio224© 2012 ATEÏSTo enable or disable moving an object by multiple pixels at a time.Layero Add Layer Add a layer of graphic editor.o Remove

System Functionality 225© 2012 ATEÏS5.1.9 Comoponent EditingPosition OperationPosition Operation Type Some functions, as Alignment or Pack use a refer

Ateis Studio226© 2012 ATEÏSo Reference Component In Reference Component mode, the reference is a component. If you select severalcomponent

System Functionality 227© 2012 ATEÏSAlignment You can select several elements (by maintaining left click and move the mouse you will have aselection

Ateis Studio228© 2012 ATEÏSYou can select several elements (by maintaining left click and move the mouse you will have aselection square) then you can

System Functionality 229© 2012 ATEÏSYou can select several component (by maintaining left click and move the mouse you will have aselection square) t

Quick Start 23© 2012 ATEÏSThen, the update process start, and pop a window after update file is transferred to device, click[Yes] to restart dev

Ateis Studio230© 2012 ATEÏSRight Angle Select Right Angle if you want to draw the wire only with right angles (90 degrees).Auto Corner Select Auto Cor

System Functionality 231© 2012 ATEÏSSignal Path Temporary In this mode, by selecting a signal link, the signal link and the entire signal path linked

Ateis Studio232© 2012 ATEÏS5.1.10 ToolsBy changing skin you modify the global style (colour and appearance) of the windows. You can chooseone of the s

System Functionality 233© 2012 ATEÏSMc Skin

Ateis Studio234© 2012 ATEÏSLondon Liquid Sky

System Functionality 235© 2012 ATEÏS5.1.11 OperationIn this menu you will find the major operations related to system connection, allowing to co

Ateis Studio236© 2012 ATEÏSMaster Preset SelectorThe combo box close to text "Master Preset" to switch master preset.Master Preset SettingsO

System Functionality 237© 2012 ATEÏSIn this topic you will find tools to re-arrange windows or find hidden opened windows.Close Close the opened activ

Ateis Studio238© 2012 ATEÏSIn the bottom of the window menu, you will find all the opened windows of your project. By selectingof the windows in the l

System Functionality 239© 2012 ATEÏSOn the left is component template and right is design window. There are three pages of componenttemplate

Ateis Studio24© 2012 ATEÏStodoEng verCheck device version using step 9 again, the version should become compatible this time, if versionis compatible,

Ateis Studio240© 2012 ATEÏS5.1.15 Resource ManagerResource manager is a container for files can be used in device configuration. Sections lis

System Functionality 241© 2012 ATEÏSDeleteRemove selected files from resource manager.ExportExport selected files to a single resource packed file.Imp

Ateis Studio242© 2012 ATEÏSCurrentIndicate which layer is current layer. The newly created objects will put into current layer.LockLock selected layer

System Functionality 243© 2012 ATEÏS5.1.19 PropertiesProperties window allow user to browse/edit settings of selected objects in design window.

Ateis Studio244© 2012 ATEÏS5.1.20 Message LibraryMessage Library provides a easy interface to manage messages used in Ateis Studio. By click menu[

System Functionality 245© 2012 ATEÏS5.1.21 Logo LibraryLogo Library is a settings windows about Logo Library management. By click menu [Vi

Ateis Studio246© 2012 ATEÏS5.2.2 Master PresetsThe Master-Preset function allows switching between several designs on the same device. Each Master-Pre

System Functionality 247© 2012 ATEÏSMaster Preset NameThe name of master preset.EditBy clicking ellipsis cell in grid you can open the dsp design wind

Ateis Studio248© 2012 ATEÏSRemoveTo remove selected master preset.Master Preset SwitchingThere is always only one master preset active at the same tim

System Functionality 249© 2012 ATEÏSMaster Preset Combo BoxBy clicking this combo box, you can switch to desired master preset and then edit sub-prese

Quick Start 25© 2012 ATEÏSA window [Set Audio Module] opened, click button [Create].

Ateis Studio250© 2012 ATEÏSTable of linked elementsThis table list all elements controlled by the sub-preset, on the right there is a s

System Functionality 251© 2012 ATEÏS5.3 Event Management5.3.1 Event ManagerThere are various type of events for controlling Ateis devices. For exampl

Ateis Studio252© 2012 ATEÏSAdd an event to event manager, Some event can't create in this window, like paging event, you needto create it in sett

System Functionality 253© 2012 ATEÏSThen a window shows brief information of the relationship state and value:Click field [Content] of event manager w

Ateis Studio254© 2012 ATEÏSState PagesThere is a page for each state in value trigger event. To switch states, click the tab of desiredstate.ElementIn

System Functionality 255© 2012 ATEÏSClick button [Add] to create a new event, a second window open to query you which kind of event isdesired. Select

Ateis Studio256© 2012 ATEÏSOn the right side of window, there is a knob to simulate source that triggers event. If you adjust theknob, the value of el

System Functionality 257© 2012 ATEÏSCloseClose the settings window.5.3.4 Step Trigger EventDescriptionThis event is used to control the element

Ateis Studio258© 2012 ATEÏSThen a window shows brief information, click select check box at row "All":Click field [Content] of event manager

System Functionality 259© 2012 ATEÏSState PagesThere is a page for each state in step trigger event. To switch states, click the tab of desiredstat

Ateis Studio26© 2012 ATEÏSThen a IDA8C block is created for further configuration.13.Add Tone component and connect to Output componentDouble click on

Ateis Studio260© 2012 ATEÏSClick button [Add] to create a new event, a second window open to query you which kind of event isdesired. Select item [Ste

System Functionality 261© 2012 ATEÏSIndicate which system contains device prior mentioned.RemoveRemove the element controlled by the event. This opera

Ateis Studio262© 2012 ATEÏSSpecify which master preset links to the state.OpenOpen settings window of the master preset.5.3.7 Sub-Preset Change EvnetD

System Functionality 263© 2012 ATEÏSOpen settings window of the sub preset.5.3.8 Intergration Paging EventThis event is used to select zones of Netw

Ateis Studio264© 2012 ATEÏSAteis NetDisplay Ateis Net ID by (X, Y) format, where X is the global net ID and Y is local net ID.Serial NumberSerial Numb

System Functionality 265© 2012 ATEÏSIf you already known the IP address of a device, you can search it by that address.Select the [Device Management]

Ateis Studio266© 2012 ATEÏS3. Click [Update] to open the update window.4. Select in the list your device, and then click on [OK].5. The browser open,

System Functionality 267© 2012 ATEÏS6. When the update is done, a pop-up window appears asking if you want the restart the device. This isnecessary, s

Ateis Studio268© 2012 ATEÏS5.4.4 Ateis Net DeployingThis function allow user to config networking state of devices on Ateis Net. When devices is first

System Functionality 269© 2012 ATEÏSIDThe internal identification for each remote devices.Remote TypeTo specify which type of remote device belong to

Quick Start 27© 2012 ATEÏS14.ConnectConnect to device.15.StoreClick store button on tools bar.

Ateis Studio270© 2012 ATEÏS5.4.6 ReverseThis function allow user to reverse design from audio processors.1. Open Device Management Window.2. Search an

System Functionality 271© 2012 ATEÏS5.5.1.3 3rd Party Control ListThis window list all elements available for 3rd party controlling. To open this wind

Ateis Studio272© 2012 ATEÏSto provide information of command string for 3rd party device to control element. The right is a visualobject allow

System Functionality 273© 2012 ATEÏSUser AccountIt allow you to create or remove users for controlling system. For each user, you can set it's

Ateis Studio274© 2012 ATEÏSThe right of updating firmware of Ateis devices.System(Para. R/W)The right of reading or writing parameters in Ateis device

System Functionality 275© 2012 ATEÏSLevelThe level user belongs to.LinkA ellipsis button to switch page to [Levels], and focus on the level that user

Ateis Studio276© 2012 ATEÏSAEC ParametersParameterRangeCommentEcho Detectled This led lit when an echo is detected.Signalled This led lit when an audi

Components of Audio Processor 277© 2012 ATEÏSParameterRangeCommentFar-EndVolume Vu-meter(dB)Audio volume of the Far-end audio signal.Near-EndVolume (d

Ateis Studio278© 2012 ATEÏSAEC Coefficient / Reset On each channel you can independently activate the echo cancellation process by setting the "A

Components of Audio Processor 279© 2012 ATEÏSvolume level.If you want to modify the volume of a source (near-end inputs), then you have to use the &qu

Ateis Studio28© 2012 ATEÏSA window [Store] is opened and store process start, during the process, system will ask user to turnon or off audio, click Y

Ateis Studio280© 2012 ATEÏSThe NLP threshold parameter is not available, the threshold is now automatically set.6.2 Delay (Advanced)Component Template

Components of Audio Processor 281© 2012 ATEÏSTo delay the audio signal input to the component. Delay component record audio into a internal

Ateis Studio282© 2012 ATEÏSTypeMaximum5ms5 µs50ms20 µs100ms20 µs200ms20 µs500ms20 µs1000ms20 µs2000ms20 µs*3: Maximum value of Distance is depend on t

Components of Audio Processor 283© 2012 ATEÏSmiddle of the room. but in this case listeners will receive sound from speakers with time differencedue t

Ateis Studio284© 2012 ATEÏS6.3 Delay (Basic)Component TemplateComponent AppearanceDescriptionTo delay the audio signal input to the component. This co

Components of Audio Processor 285© 2012 ATEÏS(Advanced) that is not allowed to mute or bypass the signal of input. There are two ways to adjustdelay

Ateis Studio286© 2012 ATEÏSTypeMaximum1000ms20 µs2000ms20 µs*3: Maximum value of Distance is depend on the type of Delay (Basic)TypeMaximum5ms1.62 m50

Components of Audio Processor 287© 2012 ATEÏS6.4 Dynamic6.4.1 AGC\AGC StereoComponent TemplateComponent AppearanceDescriptionWith this Automatic Gain

Ateis Studio288© 2012 ATEÏSThe control window of AGC Stereo the same as AGC's.Element PropertiesNameInitialMinimumMaximumPrecisionUnitReleaseOn--

Components of Audio Processor 289© 2012 ATEÏSDetermine the maximum of automatic gain. Limit the max gain to keep a natural audio dynamic.Attack TimeAd

Quick Start 29© 2012 ATEÏSNow you should see channel 1 meter as figure shown and hear a 2k tone from speaker connect toAmplifier Zone Output(zone1) on

Ateis Studio290© 2012 ATEÏSTarget level: We want a final target level at -10dB.Maximum gain: Set at 10dB, because giving more gain will generate

Components of Audio Processor 291© 2012 ATEÏS6.4.2 Auto Noise Gain (A.N.G)Component TemplateComponent AppearanceS.M: Sensing microphone inputP.M: Pagi

Ateis Studio292© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitMin Gain-6.0-15.000.1dBMax Gain6.0015.00.1dBSampling Time5050600005

Components of Audio Processor 293© 2012 ATEÏSItem list of Response Speed:No.Name1Low2Medium3HighElement DescriptionMin GainThe minimum level compensat

Ateis Studio294© 2012 ATEÏSThat's means the speed to adapt the P.M. audio level depending of the ambient noise.Paging ActivityLight on when the p

Components of Audio Processor 295© 2012 ATEÏS6. Now look the Over/Under red led:-If both Over/Under led are OFF, it means the calibration has properly

Ateis Studio296© 2012 ATEÏSlevel is not stable around0 dB, user could adjust the gain of output function, amplifier orsensing microphon

Components of Audio Processor 297© 2012 ATEÏSAs the noise level is near than during the calibration, the differential level is almost null. You can se

Ateis Studio298© 2012 ATEÏS"Fast Increase Zone" which means that the gain must be quickly increased to compensate the loudambient noise.

Components of Audio Processor 299© 2012 ATEÏS6.4.3 Compressor\Compressor StereoComponent TemplateComponent AppearanceDescriptionA Compressor is an aut

3Contents3© 2012 ATEÏSTable of Contents0Introduction 10...

Ateis Studio30© 2012 ATEÏS4.1.1 IDA8C4.1.1.1 OverviewIDA8C Controller unit enables operators to see a detailed overview of the operational status of t

Ateis Studio300© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----Soft KneeOn----CompressOff----Ratio2.01.120.00.1-Thres

Components of Audio Processor 301© 2012 ATEÏSCompressIndicates compression.RatioSets compression ratio.ThresholdSets the threshold level above which c

Ateis Studio302© 2012 ATEÏSRelease TimeSets the time it takes to release gain reduction. The 'release phase' is the period when

Components of Audio Processor 303© 2012 ATEÏSo Y: Output signal level(dB)Control Pointso Blue: Adjust Threshold.o Red: Adjust Threshold Range.o Yellow

Ateis Studio304© 2012 ATEÏS Comp-limiter is a combination of the Compressor and the Limiter Components.Control WindowElement PropertiesNameInitialMin

Components of Audio Processor 305© 2012 ATEÏSHard Clipping(Limiter)Enables/disables the “Hard clipping” mode.Threshold(Limiter)Sets the threshold leve

Ateis Studio306© 2012 ATEÏSAxiso X: Input signal level (dB)o Y: Output signal level (dB)Control Pointso Blue: Adjust Threshold(Compressor).o Red: Adju

Components of Audio Processor 307© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitMin Gain-6.0-15.000.1dBMax Gain6.0015.00.1dBSampl

Ateis Studio308© 2012 ATEÏSElement DescriptionMin GainThe minimum AGC level compensation.Max GainThe maximum AGC level compensation.Sampling TimeDeter

Components of Audio Processor 309© 2012 ATEÏSDecrease ZoneIndicates that the AGC gain is decreasing.Dead ZoneIndicates that the AGC is not changing.In

Product Features 31© 2012 ATEÏSIDA8C Controller unit is easily configured with our PC based ATEÏS-Studio global software (Windowscompatible). So

Ateis Studio310© 2012 ATEÏS6.4.6 Ducker\Ducker StereoComponent TemplateComponent AppearanceDescriptionThe Ducker is a kind of “sophisticated switch” a

Components of Audio Processor 311© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitBypassOff----ActiveOff----Thd.-20.0-80.035.00.1dBResponse Time10010

Ateis Studio312© 2012 ATEÏSAs simple example, we will set a system for a speaker with background music. When the speakeris talking, the background mus

Components of Audio Processor 313© 2012 ATEÏS6.4.7 Expander\Expander StereoComponent TemplateComponent AppearanceDescriptionAn expander works in an op

Ateis Studio314© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----Soft KneeOn----ExpandOff----Ratio2.01.020.00.1x;1Thres

Components of Audio Processor 315© 2012 ATEÏSRelease TimeAdjusts the time to stop the gain reduction.Gain ReductionReflects the current amount of gain

Ateis Studio316© 2012 ATEÏS6.4.8 Gate6.4.8.1 Gate - MonoComponent TemplateComponent AppearanceDescriptionThe gate allows you to cut off the signal bel

Components of Audio Processor 317© 2012 ATEÏSControl WindowElement PropertiesNameInitialMinimumMaximumPrecisionUnitMuteOff----BypassOff----Gate OnOff-

Ateis Studio318© 2012 ATEÏSAdjust the time between the level's detection and the beginning of the Gate operation.Attack TimeAdjust the fade-in ti

Components of Audio Processor 319© 2012 ATEÏSDescriptionSimple double channel Gate.Control WindowElement PropertiesNameInitialMinimumMaximumPrecisionU

Ateis Studio32© 2012 ATEÏS G.Fault LEDThis LED lights on when a global fault is detected.Note: Fault LED and system fault LED are exclusive, if system

Ateis Studio320© 2012 ATEÏSSet the volume of the signal connected in the input R.Thd.Sets the threshold level above which Gate will open.Response Time

Components of Audio Processor 321© 2012 ATEÏS6.4.8.3 Gate - VoiceComponent TemplateComponent AppearanceDescriptionThis component is gate which is usin

Ateis Studio322© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitGate OnOff----MuteOff----BypassOff----Thd.-20.0-90.035.00.1dBHold T

Components of Audio Processor 323© 2012 ATEÏSVoice Recognition6.4.8.4 Gate with SidechainComponent TemplateComponent AppearanceDescriptionWith this ga

Ateis Studio324© 2012 ATEÏSControl WindowElement PropertiesNameInitialMinimumMaximumPrecisionUnitMuteOff----BypassOff----Gate OnOff----Sidechain Gain0

Components of Audio Processor 325© 2012 ATEÏSFlash when the gate is active (open).Sidechain GainSet the volume of the signal connected in the input S.

Ateis Studio326© 2012 ATEÏS6.4.9 Limiter\Limiter StereoComponent TemplateComponent AppearanceDescriptionThis component limits the audio level dependin

Components of Audio Processor 327© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----Hard ClippingOn----LimitingOff----Th

Ateis Studio328© 2012 ATEÏSLimitingIndicates limiting.ThresholdSets the threshold level above which limiting begins.Release TimeSets the time it takes

Components of Audio Processor 329© 2012 ATEÏSo Y: Output signal level(dB)Control Pointso Red: Adjust Threshold.6.5 Equalizer6.5.1 GEQ\GEQ StereoCompon

Product Features 33© 2012 ATEÏS Zone Fault LEDsTo show fault status of zone. This LED light on if one of following faults is detected:Normal AMP Error

Ateis Studio330© 2012 ATEÏSGEQ is abbreviation of graphic equalizer, in the graphic equalizer, the input signal is sent to a bankof filters. Each filt

Components of Audio Processor 331© 2012 ATEÏSAxiso X: Frequency of output signal(Hz)o Y: Gain of output signal(dB)Control Pointso Blue: Adjust Gain.Ap

Ateis Studio332© 2012 ATEÏS6.5.2 PEQ\PEQ StereoComponent TemplateComponent AppearanceDescriptionPEQ is abbreviation of parametric equalizer, PEQs a

Components of Audio Processor 333© 2012 ATEÏSControl WindowElement PropertiesGenerate InformationNameInitialMinimumMaximumPrecisionUnitBypass allOff--

Ateis Studio334© 2012 ATEÏSSet the gain (attenuate or increase the selected frequency).Graphical Control WindowAxiso X: Frequency of output signal(Hz)

Components of Audio Processor 335© 2012 ATEÏS6.6 FeedbackComponent TemplateComponent AppearanceDescriptionThe error between the desired and the actual

Ateis Studio336© 2012 ATEÏSdetects feedback and attenuates the responsible frequency. There is several kind of feedbackcomponent. The di

Components of Audio Processor 337© 2012 ATEÏSElement DescriptionBypassBypass the feedback’s module. By clicking on Bypass you will erase the captured

Ateis Studio338© 2012 ATEÏStodoLock TimeInterval time during the filter will be active when a feedback is detected. After that the capturedvalues will

Components of Audio Processor 339© 2012 ATEÏSControl WindowElement PropertiesGenerate InformationNameInitialMinimumMaximumPrecisionUnitBypass AllOff--

Ateis Studio34© 2012 ATEÏSconnector of 100V audio coming from amplifierIDA8 output exactly the same audio signal to line A and B. Two speakers can con

Ateis Studio340© 2012 ATEÏSAxiso X: Frequency of output signal(Hz)o Y: Gain of output signal(dB) (Kevin)Control Pointso Blue: Adjust Frequencyo Yellow

Components of Audio Processor 341© 2012 ATEÏSDescriptionA Band Pass component that passes frequencies within a certain range and rejects (atte

Ateis Studio342© 2012 ATEÏSType of filtering, SlopeSlope of attenuation.BandwidthDifference between the upper and lower frequencies in a contiguou

Components of Audio Processor 343© 2012 ATEÏS6.7.3 Band StopComponent TemplateComponent AppearanceDescriptionA Band Stop filter is a filter that p

Ateis Studio344© 2012 ATEÏSGenerate InformationNameInitialMinimumMaximumPrecisionUnitModeButterworth----Slope12dB----Bandwidth1.000.012.000.01OctaveBy

Components of Audio Processor 345© 2012 ATEÏSAxiso X: Frequency of output signal(Hz)o Y: Level of input signal(dB)Control Pointso Blue: Adjust element

Ateis Studio346© 2012 ATEÏS6.7.4 Crossover/Crossover StereoComponent TemplateComponent AppearanceDescriptionCrossovers split the audio signal into

Components of Audio Processor 347© 2012 ATEÏS*1: The Initial/Minimum/Maximum values are different between types of Crossover/Crossover Stereo.NameInit

Ateis Studio348© 2012 ATEÏSAxiso X: Frequency of output signal(Hz)o Y: Level of input signal(dB)Control Pointso Blue: Adjust Level and hi-pass Freque

Components of Audio Processor 349© 2012 ATEÏS6.7.5 Hi/Lo PassComponent TemplateComponent AppearanceDescriptionHi/Lo Pass component passes high/lo freq

Product Features 35© 2012 ATEÏSOptional card to build a global dedicated IDA8C network. Configurable Audio I/OsTwo configurable 0dB audio I/O port

Ateis Studio350© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitModeBessel 6 dB----TypeLow-Pass----BypassOff----MuteOff----Level0-90.020.00.1dBFreque

Components of Audio Processor 351© 2012 ATEÏSAxiso X: Frequency of output signal(Hz)o Y: Level of input signal(dB)Control Pointso Red: Adjust element

Ateis Studio352© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitModeButterworth----Slope12dB----Bandwidth10.012.000.01OctaveBypassO

Components of Audio Processor 353© 2012 ATEÏSThe center frequency to be cut.Graphical Control WindowAxiso X: Frequency of output signal(Hz).o Y: Level

Ateis Studio354© 2012 ATEÏS6.7.7 Shelving FilterComponent TemplateComponent AppearanceDescriptionShelving Filter component implements a first order re

Components of Audio Processor 355© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitBypassOff----Level0-90.020.00.1dBFrequency100010220001HzElement Des

Ateis Studio356© 2012 ATEÏS6.8 FiremanComponent TemplateComponent AppearanceDescriptionThis component represent Fireman Microphone with one channel au

Components of Audio Processor 357© 2012 ATEÏSSignal level of Fireman component. Paging-Event SelectionSelect paging event to bind with Fireman compone

Ateis Studio358© 2012 ATEÏSDescriptionControl the input signals parameters and monitor it. The analogue input modules represent thephysica

Components of Audio Processor 359© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitOverload Thd.0-20.020.00.1dBElement DescriptionBypassBypass audio o

Ateis Studio36© 2012 ATEÏS4.1.1.4 CharacteristicsCaseDimension = 436mm (W) x 313mm (L) x 88mm (H).Weight = 5.36Kg.Color = RAL7016.Screen3.5" Col

Ateis Studio360© 2012 ATEÏS6.9.2 Mono InputComponent TemplateComponent AppearanceDescriptionFor AES/EBU input, the elements inside the component is v

Components of Audio Processor 361© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff----

Ateis Studio362© 2012 ATEÏSVolumeMeter showing the channel RMS level.SignalIndicates audio signal presence above -30 dB from chosen 'Sensitivity&

Components of Audio Processor 363© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff----

Ateis Studio364© 2012 ATEÏSVolumeMeter showing the channel RMS level.SignalIndicates audio signal presence above -30 dB from chosen 'Sensitivity&

Components of Audio Processor 365© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff----

Ateis Studio366© 2012 ATEÏSVolumeMeter showing the channel RMS level.SignalIndicates audio signal presence above -30 dB from chosen 'Sensitivity&

Components of Audio Processor 367© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitMuteOff----InvertOff----Element DescriptionMuteMute the inverter mo

Ateis Studio368© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----Input Level0-90.020.00.1dBOutput Level0-90.

Components of Audio Processor 369© 2012 ATEÏS6.11 Local Echo SuppressorComponent TemplateComponent AppearanceDescriptionThis component is designed for

Product Features 37© 2012 ATEÏSTHD @ 1kHz = < 1%.Bandwidth @ -3dB = 100Hz ~ 12kHz.Configurable Audio OutputMaximum level = 14 dBuOutput Impedance =

Ateis Studio370© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----Gain Reduction0-25.000.1dBPre-Processing Threshold-22.

Components of Audio Processor 371© 2012 ATEÏSPost-Processing ThresholdWhen input volume is smaller than Post-Processing Threshold ,it will suppress th

Ateis Studio372© 2012 ATEÏS6.12.2 EVAC BoardComponent TemplateComponent AppearanceDescriptionThis component is corresponds to URGP peripheral devices,

Components of Audio Processor 373© 2012 ATEÏSTypeTo specify mode of activate, there are two chooses:o N.O.Normally open, close the contact to output s

Ateis Studio374© 2012 ATEÏS6.12.3 Evacution InputComponent TemplateComponent AppearanceDescriptionThis component corresponds to the Evacuation Input

Components of Audio Processor 375© 2012 ATEÏSParametersMonitor ModeThere are two options:o Voltage:Logic output of component trigger by a voltage pola

Ateis Studio376© 2012 ATEÏS6.12.4.1 TriggerComponent TemplateComponent AppearanceDescriptionThis component link events to logic signal, linked events

Components of Audio Processor 377© 2012 ATEÏSAfter events is linked to the component the control window list it in grids:ParametersEvent NameShow the

Ateis Studio378© 2012 ATEÏSIn above figure, the logic output channel 4 and 6 are selected. to detail settings click the gridcell [...]:In above f

Components of Audio Processor 379© 2012 ATEÏSDescriptionThis component allow user to generate logic signal using button in software. For each channel

Ateis Studio38© 2012 ATEÏSInput Impedance = 10k OhmTHD+N(Total Harmonic Distortion plus Noise)SensitivityMinimumMaximumUnitFrequency0dBu-0.04%20~20kHz

Ateis Studio380© 2012 ATEÏS6.12.7 Logic Net InputComponent TemplateComponent AppearanceDescriptionThis component transfer logic signals over Ateis Net

Components of Audio Processor 381© 2012 ATEÏS6.12.8 Logic Net OutputComponent TemplateComponent AppearanceDescriptionThis component transfer logic sig

Ateis Studio382© 2012 ATEÏS6.12.9 NOTComponent TemplateComponent AppearanceDescriptionThis component performs logic not operation.6.12.10 ORComponent

Components of Audio Processor 383© 2012 ATEÏSComponent AppearanceDescriptionThis component performs logic or operation.6.12.11 OutputComponent Templat

Ateis Studio384© 2012 ATEÏS6.12.12 SchedulerComponent TemplateComponent AppearanceDescriptionThis component allow user to arrange the timing of genera

Components of Audio Processor 385© 2012 ATEÏSScheduler ListOn the left side of window, there is a box to list all channels of scheduler. Click it can

Ateis Studio386© 2012 ATEÏSSpecify the condition to deactivate scheduler, there are three kinds of stop condition:ContinueIn this option, scheduler ne

Components of Audio Processor 387© 2012 ATEÏSThe Occurrence parameter determines the cycle type of triggering, there are five types available:Hourly/D

Ateis Studio388© 2012 ATEÏS6.13 Meter6.13.1 Peak/RMS MeterComponent TemplateComponent AppearanceDescriptionThis component display the amplitude of

Components of Audio Processor 389© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitIndefiniteOff----Measure TypeRMS----Hold Time1010

Product Features 39© 2012 ATEÏS4.1.1.5 PeripheralsFollowing table is the peripherals supported by IDA8C:DeviceConnectionMax. NumFunctionFireman MICFir

Ateis Studio390© 2012 ATEÏS6.14 Message6.14.1 Message PlayerComponent TemplateComponent AppearanceDescriptionThis component play the audio message

Components of Audio Processor 391© 2012 ATEÏS6.14.2 MM PlayerComponent TemplateComponent AppearanceDescriptionThis component play the messages stored

Ateis Studio392© 2012 ATEÏS6.15 Mixer6.15.1 AutoMixerComponent TemplateComponent AppearanceDescriptionThis component Allows mix several signals to one

Components of Audio Processor 393© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitTypeManual----Last Mic. On DesignatedChannel 1---

Ateis Studio394© 2012 ATEÏSManual mode : Only manual channel activation (threshold and priority are ignored).Automatic mode : With priority and thres

Components of Audio Processor 395© 2012 ATEÏSNOM Attenuation StepSets the amount of attenuation to be applied each time the number of act

Ateis Studio396© 2012 ATEÏSThis component Allows mix several signals to one output. The Activation of channel(s) can be donemanually or automatically

Components of Audio Processor 397© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitMatrix Output MuteOff----Matrix Output Level0-90.000.1dBOutput Leve

Ateis Studio398© 2012 ATEÏSMatrix Output MuteMute the input for the output mixing. This is different with the Mute element, this element onlyaffect th

Components of Audio Processor 399© 2012 ATEÏS6.15.3 MatrixComponent TemplateComponent AppearanceDescriptionMatrix Mixers offer three main functionalit

Ateis Studio4© 2012 ATEÏS...

Ateis Studio40© 2012 ATEÏSProtocolInterfaceFunctionConnectionSettingsRead Monitoring StatusRead Evacuation StatusPlay MessageLogic I/O Control4.1.2 ID

Ateis Studio400© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitInput MuteOff----Input Level0-60.020.00.1dBOutput Level0-60.020.00.

Components of Audio Processor 401© 2012 ATEÏS6.15.4 StandardComponent TemplateComponent AppearanceDescriptionThe matrix module is similar to the stand

Ateis Studio402© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitInput MuteOff----Input Level0-90.020.00.1dBOutput MuteOff----Output

Components of Audio Processor 403© 2012 ATEÏSDescriptionThis component transfer audio signals over Ateis Net.The signal goes into a channel of Net Out

Ateis Studio404© 2012 ATEÏS6.17 Net OutputComponent TemplateComponent AppearanceDescriptionThis component transfer audio signals over Ateis Net. It mu

Components of Audio Processor 405© 2012 ATEÏS6.18 Noise Generator6.18.1 PinkComponent TemplateComponent AppearanceDescriptionPink noise or 1/ƒ noise

Ateis Studio406© 2012 ATEÏSMuteMute the sound coming out from the component.LevelLevel of the pink noise.6.18.2 ToneComponent TemplateComponent Appear

Components of Audio Processor 407© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitLevel-100.0-100.020.00.1dBTone freq.100020200001H

Ateis Studio408© 2012 ATEÏS6.18.3 WhiteComponent TemplateComponent AppearanceDescriptionThis component generates a White noise. The White noise is a r

Components of Audio Processor 409© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitMute-----Level-100.0-100.020.00.1dBElement DescriptionMuteMute the

Product Features 41© 2012 ATEÏSThe Network cards that comes with the unit provides a redundant 48 channels audio and dataconnection, At

Ateis Studio410© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----Le

Components of Audio Processor 411© 2012 ATEÏSLevelSignal output level of the module.Overload thd.Sets the threshold of the overload indicator. 6.19.2

Ateis Studio412© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----Le

Components of Audio Processor 413© 2012 ATEÏSLevelSignal output level of the module.Overload thd.Sets the threshold of the overload indicator. 6.19.3

Ateis Studio414© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----Le

Components of Audio Processor 415© 2012 ATEÏSLevelSignal output level of the module.Overload thd.Sets the threshold of the overload indicator. 6.19.4

Ateis Studio416© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----Le

Components of Audio Processor 417© 2012 ATEÏSLevelSignal output level of the module.Overload thd.Sets the threshold of the overload indicator.6.19.5

Ateis Studio418© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----Le

Components of Audio Processor 419© 2012 ATEÏSLevelSignal output level of the module.Overload thd.Sets the threshold of the overload indicator.6.20 Pa

Ateis Studio42© 2012 ATEÏSTo show fault status of zone. This LED light on if one of following faults is detected:Normal AMP ErrorLine A ErrorLine B Er

Ateis Studio420© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitActivationFixed----TTL InOff----Priority*1----Gate OnOff----SoloOff

Components of Audio Processor 421© 2012 ATEÏSFlash when the gate is active (open).SoloRoute this input.BusyLit if the gate of the channel is o

Ateis Studio422© 2012 ATEÏSDescriptionThe job of Network Paging component is to route input source signal to zones using priorityarbitr

Components of Audio Processor 423© 2012 ATEÏSA source type is an identification for paging activities. If a zone if occupy by some source for paging,i

Ateis Studio424© 2012 ATEÏSEvacEnable this option to set the paging source is an evacuation source. If an evacuation source isactive on paging, A

Components of Audio Processor 425© 2012 ATEÏSThere are various mode for triggering a paging activity.o NoneThe paging request is not coming from the N

Ateis Studio426© 2012 ATEÏSA paging request of the channel is established depend on the logic signal of input.Basically if logic from lo to hi, i

Components of Audio Processor 427© 2012 ATEÏSCodeA code is a zone combination so called a selection of zones, the figure above is anexample, th

Ateis Studio428© 2012 ATEÏSButton AddAdd codes to event; Button RemoveRemove selected code.o SingularThis event is very similar with integration pagin

Components of Audio Processor 429© 2012 ATEÏSThis is the condition to determine a paging request can be allowed or denied. If the percentageof availab

Product Features 43© 2012 ATEÏSTwo RJ-45 connectors to connect consoles or peripheral devices. For examples, PSS AS, URCAS, PPM AS, ... are c

Ateis Studio430© 2012 ATEÏSLogic Out TriggerThere 20 channel logic output for each Network Paging component, this section shows theconfig

Components of Audio Processor 431© 2012 ATEÏSIt is able to output a logical hi to a specific output channel in condition of zone occup

Ateis Studio432© 2012 ATEÏS6.22 RS485 Audio6.22.1 RS485 InputComponent TemplateComponent AppearanceDescriptionThis component control the RS485 input

Components of Audio Processor 433© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff----

Ateis Studio434© 2012 ATEÏSThis LED light up if the signal of input channel greater than Overload Thd.VolumeMeter showing the channel RMS level.Signal

Components of Audio Processor 435© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-20.0-20.020.00.1dBMuteOff--

Ateis Studio436© 2012 ATEÏSLevelSignal output level of the module.Overload Thd.Sets the threshold of the overload indicator.6.23 SelectorComponent Te

Components of Audio Processor 437© 2012 ATEÏSElement DescriptionInput Select6.24 Signal MonitorComponent TemplateComponent AppearanceDescriptionThis c

Ateis Studio438© 2012 ATEÏSElement PropertiesNameInitialMinimumMaximumPrecisionUnitTrigger OnOff----Threshold-20.0-50.020.00.1dBVolume-40.0-40.020.00.

Components of Audio Processor 439© 2012 ATEÏS6.25 Telephone Card6.25.1 TC TransmitComponent TemplateComponent AppearanceDescriptionThis component allo

Ateis Studio44© 2012 ATEÏSDC Input18V~26V, Typical 24V2A-DC Output18V~26V, Typical 24V0.5A-AC Maximum Consumption = 45 W.Amplifier Zone OutputsMaximum

Ateis Studio440© 2012 ATEÏSM: MCU statusControl WindowElement PropertiesNameInitialMinimumMaximumPrecisionUnitDialingOff----RingingOff----SetOff----Re

Components of Audio Processor 441© 2012 ATEÏSDigit KeysDigit keys are the buttons with circled shape on the left part of control window. There

Ateis Studio442© 2012 ATEÏSFlashThis button to make a 3-way calling, During the connection of first remote phone, press thisbutton, then dia

Components of Audio Processor 443© 2012 ATEÏSControl WindowElement PropertiesNameInitialMinimumMaximumPrecisionUnitCaller MuteOff----Caller Level0-15.

Ateis Studio444© 2012 ATEÏSHistoryDisplay the DTMF number ever detected.Phone AnswerThe mode of action for answering incoming calls. There are two kin

Components of Audio Processor 445© 2012 ATEÏSThis component is an bridge between Ateis device and Voxnet devices. It map the key in voxnetprot

Ateis Studio446© 2012 ATEÏS3047BP ROTTERDAM, NETHERLANDSPhone +31 (0)10 2088690Fax +31 (0)10 2088699Ateis Suisse SAAddress:Chemin du Dévent1024 Ecuble

Product Features 45© 2012 ATEÏSBandwidth = 20Hz ~ 20kHz.EIN(Equivalent Input Noise)SensitivityMinimumMaximumUnitFrequency0dBu--81dBu20~20kHz@150Ù-12dB

Ateis Studio46© 2012 ATEÏSMaximum Output Level = 10 dBu.Output Impedance = 300 Ohm.THD @ 1kHz at output < 0.02.Bandwidth @ -3dB at output = 20Hz ~

Product Features 47© 2012 ATEÏSDeviceConnectionMax. NumFunctionDNMPDC1/PDCAuto noise gain for audio signals.PPM-IT5Ethernet1 ActiveOver EthPaging, Ele

Ateis Studio48© 2012 ATEÏS4.1.3 IDA8SL4.1.3.1 OverviewThe IDA8SL Slave units provide audio output expansion of the IDA8 Systems using a

Product Features 49© 2012 ATEÏS4.1.3.2 Front Panel System Fault LEDThis LED lights on when a system fault fault is detected. G.Fault LEDThis LED light

5Contents5© 2012 ATEÏS...

Ateis Studio50© 2012 ATEÏSLine B ErrorBackup AMP ErrorAMP Line Leakage Error4.1.3.3 Rear Panel Backup Amplifier OutputThis connector connects to the o

Product Features 51© 2012 ATEÏSamplifier. Contact Outputs8 logic outputs channels to close/open circuit for an external device, this contact is normal

Ateis Studio52© 2012 ATEÏSBandwidth = 20Hz ~ 20kHz.EIN(Equivalent Input Noise)SensitivityMinimumMaximumUnitFrequency0dBu--81dBu20~20kHz@150Ù-12dBu--93

Product Features 53© 2012 ATEÏSMaximum level = 14 dBuInput Impedance = 10k OhmTHD+N(Total Harmonic Distortion plus Noise)SensitivityMinimumMaximumUnit

Ateis Studio54© 2012 ATEÏSEvacuation Inputs(Voltage Mode)On Voltage:ItemMinimumMaximumUnitVoltage1872VDCContact Outputs + EVAC, Fault State OutputsIte

Product Features 55© 2012 ATEÏSDeviceConnectionMax. NumFunctionzones.CD TouchPDC1/PDCWall mounted cabinet remote paging console with touch screenand F

Ateis Studio56© 2012 ATEÏSchannel audio and data network over CAT5 or fiber optic. Each IDA8S expands the IDA8 System with anadditional 8 outputs,

Product Features 57© 2012 ATEÏSTo show fault status of zone. This LED light on if one of following faults is detected:Normal AMP ErrorLine Speaker Err

Ateis Studio58© 2012 ATEÏS8 logic outputs channels to close/open circuit for an external device, this contact is normally open. Evacuation Inputs9 eva

Product Features 59© 2012 ATEÏSSpeaker line/AmplifierMaximum Power = 700W(RMS).Maximum Power(Siren + Message) = 1000W.Configurable Audio OutputMaximum

Ateis Studio6© 2012 ATEÏS...

Ateis Studio60© 2012 ATEÏSMaximum level = 14 dBuInput Impedance = 10k OhmTHD+N(Total Harmonic Distortion plus Noise)SensitivityMinimumMaximumUnitFrequ

Product Features 61© 2012 ATEÏS0°C ~ 40°C4.1.4.5 3rd Party ControlThe following table list 3rd Party Control protocols IDA8C Supported.ProtocolInterfa

Ateis Studio62© 2012 ATEÏSDeviceConnectionMax. NumFunctionBoxIDA8, use it, Deskpad can working without physcial connection.4.1.5 Amplifier Configurati

Product Features 63© 2012 ATEÏSBackup Amplifiers ConnectionThe connection of amplifiers for backup. In above figure(Basic Amplifier Connection),

Ateis Studio64© 2012 ATEÏSAudio Routing without Backup Am plifierThe figure(Audio Routing with Backup Amplifier) shows the amplifier backup case for a

Product Features 65© 2012 ATEÏSbackup amplifier can serve for zone 1 to zone 4 actually. The below figure shows the concept of that.Share the Backup A

Ateis Studio66© 2012 ATEÏSAdvance Backup Amplifier SetupThere are three backup amplifier groups of above figure:Backup Group1Amplifier B1 serves Zone1

Product Features 67© 2012 ATEÏSAmplifier B3 serves Zone 13 ~ zone24.Software settings for backup amplifierIt is necessary to have software settings to

Ateis Studio68© 2012 ATEÏSThe meaning of parameters list below:AmountSpecify the number of backup amplifiers in system. the list content of combo b

Product Features 69© 2012 ATEÏSWhen a fault is generated, the following things will be done by IDA8/S:System Fault LED is light on if the fault is a s

7Contents7© 2012 ATEÏS...

Ateis Studio70© 2012 ATEÏSNameDescriptionTrans ErrorAn internal hw error of device.Power ErrorThe power circuit inside device is error.TEL ErrorThe co

Product Features 71© 2012 ATEÏSText messages display at touch screen on front panel of IDA8C:"I2C Error"Text message display at window [Mach

Ateis Studio72© 2012 ATEÏSLED IndicatorWhen this error is detected, following LEDs will light up:o System Fault LED on front panel of IDA8C/S.o G. Fau

Product Features 73© 2012 ATEÏS1. Update firmware using newest version of Ateis Studio.2. Store configuration. It the problem still not solved, please

Ateis Studio74© 2012 ATEÏSText message display at window [Machine Fault Record] of Ateis Studio:Buzzer sound output to monitoring speaker on front pan

Product Features 75© 2012 ATEÏSo System Fault LED on front panel of IDA8C/S.o G. Fault LED on front panel of IDA8C/S.LogText messages display at touch

Ateis Studio76© 2012 ATEÏS4.1.6.1.11 TEL ErrorFault MeaningThe communication between main controller unit and telephone is fail.Fault IndicationLED I

Product Features 77© 2012 ATEÏSBuzzer sound output to monitoring speaker on front panel of IDA8C.Fault HandlingContact service to repair device.4.1.6.

Ateis Studio78© 2012 ATEÏSo Zone Fault LEDs on front panel of IDA8C/S.Logo Amplifier Gain Too HighText messages display at touch screen on front panel

Product Features 79© 2012 ATEÏSAmplifier Gain Too High

Ateis Studio8© 2012 ATEÏS...

Ateis Studio80© 2012 ATEÏSAmplifier Gain Too Low

Product Features 81© 2012 ATEÏSAmplifier Fail4.1.6.2.2 Line A/B ErrorFault MeaningThis error is mainly for loudspeaker connected to IDA8C/S's sp

Ateis Studio82© 2012 ATEÏSThe voltage of pin +, - is monitored by IDA8C/S, if the voltage is zero, it means there is a shortof circuit outside IDA8C/S

Product Features 83© 2012 ATEÏSBuzzer sound output to monitoring speaker on front panel of IDA8C.Fault HandlingLine A/B Open

Ateis Studio84© 2012 ATEÏSLine A/B Bad Impedance

Product Features 85© 2012 ATEÏSLine A/B Short4.1.6.2.3 Amplifier Line Leakage ErrorFault MeaningAn electricity leakage between IDA8C/S and speaker is

Ateis Studio86© 2012 ATEÏSText message display at window [Machine Fault Record] of Ateis Studio:Buzzer sound output to monitoring speaker on front pan

Product Features 87© 2012 ATEÏSText messages display at touch screen on front panel of IDA8C:"EVAC Input Error".Text message display at wind

Ateis Studio88© 2012 ATEÏSFault Handling4.1.6.2.5 Ateis Net BrokenFault MeaningAteis Net is broken, this problem may comes from wire connection betwe

Product Features 89© 2012 ATEÏSBuzzer sound output to monitoring speaker on front panel of IDA8C.Fault HandlingCheck wire connection between all IDA8C

9Contents9© 2012 ATEÏS...

Ateis Studio90© 2012 ATEÏSo Fireman Microphone Button OpenText messages display at touch screen on front panel of IDA8C:"Fireman Error""

Product Features 91© 2012 ATEÏSo G. Fault LED on front panel of IDA8C/S.LogText messages display at touch screen on front panel of IDA8C:"Fireman

Ateis Studio92© 2012 ATEÏSo G. Fault LED on front panel of IDA8C/S.LogText messages display at touch screen on front panel of IDA8C:"User Define

Product Features 93© 2012 ATEÏSFault HandlingReplace the peripheral device by a good one, if the fault is solved, the problem is coming f

Ateis Studio94© 2012 ATEÏSFault Handling4.1.6.2.11 Remote FaultFault MeaningAn error is detected on peripheral devices. For PPM AS or PSS AS, this f

Product Features 95© 2012 ATEÏSo PPM AS / PSS AS Capsule Microphone ShortText messages display at touch screen on front panel of IDA8C:"Remote Fa

Ateis Studio96© 2012 ATEÏS3. Store configuration, then online.4. Set appropriate settings for your application using Ateis Studio. you can see more

Product Features 97© 2012 ATEÏSIndicates a row is refer to which zone.MonitorEnable/Disable zone monitoring, if monitoring of a zone is disabled,

Ateis Studio98© 2012 ATEÏSMeasurementAfter parameter settings are done in lower part grid, IDA8C/S start to measure value get from internalcircuit, an

Product Features 99© 2012 ATEÏSLeakage occurrence:If leakage impedance lower than the leakage threshold which is defined in [Global Settings] tab, the